ET-P10
Dual-Rail 5 V + 3.3 V Supply
6–28 V in, 5 V 2 A + 3.3 V 600 mA, reverse protected
AED 49.00
Out of stock✓ TestedEvery board is checked before it ships
🚚 Fast shippingUAE 1–3 days · GCC & worldwide
💬 Engineer supportQuestions answered by the designers
Overview
6–28 V in, 5 V 2 A + 3.3 V 600 mA, reverse protected
The ET-P10 is built around the Diodes AP63205 (3.8–32V, 2A, 1.1MHz, 22µA Iq) + AP2112K-3.3 (600mA).
Designed in Dubai by ElectroTrical — the full schematic, BOM and design notes are published below.
Good for
- 12/24 V systems to 5 V and 3.3 V
- Robots on 2S–6S LiPo
- Industrial sensor nodes
Key features
What makes it different
Regulators
Diodes AP63205 (3.8–32V, 2A, 1.1MHz, 22µA Iq) + AP2112K-3.3 (600mA)
Input
6–28V after SS34 (screw terminal); 12V / 24V systems, 2S–6S LiPo
Outputs
5V 2A total, 3.3V 600mA from it
Open documentation
Schematic, BOM and layout notes published for every board.
Breadboard friendly
Standard 2.54 mm pitch and M2.5 mounting holes.
Specifications
Technical specifications
| Regulators | Diodes AP63205 (3.8–32V, 2A, 1.1MHz, 22µA Iq) + AP2112K-3.3 (600mA) |
|---|---|
| Input | 6–28V after SS34 (screw terminal); 12V / 24V systems, 2S–6S LiPo |
| Outputs | 5V 2A total, 3.3V 600mA from it |
| Size | 38.1 × 25.4 mm |
|---|---|
| Mounting | 4 × M2.5 holes, 2.54 mm from each corner |
| Connectors | 5-pin 2.54 mm header · Screw terminal 2P 5.0mm 17A (THT) — Input |
| Main IC | AP63205WU-7 (LCSC C2071056) |
| Revision | Rev A |
Performance
Output capacity
Pinout
Pin map and connections
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | Power | After reverse diode |
| 2 | GND | Ground | Ground |
| 3 | EN | Control | Low = off |
| 4 | 5V | Power | 2A minus 3V3 load |
| 5 | 3V3 | Power | 600mA |
Mechanical
Dimensions and what's in the box
In the box
- 1 × ET-P10 Dual-Rail 5 V + 3.3 V Supply (assembled)
- 1 × 5-pin 2.54 mm male header, unsoldered
Getting started
- Wire the header: VIN, GND, EN, 5V, 3V3
Compare
Which regulator?
| Dual-Rail 5 V + 3.3 V Supply (this board)This board | ET-P03 TPS63802 Buck-Boost 3.3 V | ET-P04 TPS563201 5 V 3 A Step-Down | ET-P05 TPS61023 5 V Boost | |
|---|---|---|---|---|
| What it does | 6–28 V in, 5 V 2 A + 3.3 V 600 mA, reverse protected | 3.3 V 2 A from 1.8–5.5 V input | 6.5–17 V in, 5 V 3 A out | 5 V 1 A from a single LiPo cell |
| Interface | 6–28V after SS34 (screw terminal); 12V / 24V… | 1.8V start, runs to 1.3V; 1S LiPo, 2–3× AA/NiMH,… | 6.5–17V (12V adapters, 3S/4S LiPo up to 16.8V) | 1S LiPo / 2-3 AA; starts at 1.8V |
| Best for | 12/24 V systems to 5 V and 3.3 V | Flat 3.3 V from a LiPo | 12 V to 5 V for Raspberry Pi | 5 V from a LiPo for NeoPixels |
| Price | 49 AED | 39 AED | 29 AED | 15 AED |
Downloads
Documents and design files
Need a custom version of this board?
Different connector, size or sensor? We design and build custom variants.