ET-MD14

High-Current MOSFET PWM Switch

Name: High-Current MOSFET PWM Switch
Brand: ElectroTrical
SKU: ET-MD14
Price: 39.00 AED
Availability: OutOfStock

Gate-driven 30 V MOSFET for 10 A loads, fast PWM from 3.3 V

AED 39.00

Out of stock

✓ TestedEvery board is checked before it ships

🚚 Fast shippingUAE 1–3 days · GCC & worldwide

💬 Engineer supportQuestions answered by the designers

Download datasheet (PDF)

Overview Key features Specifications Performance Pinout

Overview

Gate-driven 30 V MOSFET for 10 A loads, fast PWM from 3.3 V

The ET-MD14 is built around the NCE3080K N-MOSFET 30V 80A, ~6.5mΩ at 10V gate, low-side. It runs from Gate supply 10–18V (usually the 12V load supply); load supply up to 24V.

Designed in Dubai by ElectroTrical — the full schematic, BOM and design notes are published below.

Good for

Heaters and LED strips
Solenoids and pumps
High-frequency PWM loads

Key features

What makes it different

Switch

NCE3080K N-MOSFET 30V 80A, ~6.5mΩ at 10V gate, low-side

Driver

TI UCC27517 4A/4A gate driver: 3.3V logic switches the FET hard at 10–18V gate drive

Control

PWM up to 200kHz from 3.3/5V logic

Supply

Gate supply 10–18V (usually the 12V load supply); load supply up to 24V

Open documentation

Schematic, BOM and layout notes published for every board.

Breadboard friendly

Standard 2.54 mm pitch and M2.5 mounting holes.

Specifications

Technical specifications

Device
Switch	NCE3080K N-MOSFET 30V 80A, ~6.5mΩ at 10V gate, low-side
Driver	TI UCC27517 4A/4A gate driver: 3.3V logic switches the FET hard at 10–18V gate drive
Control	PWM up to 200kHz from 3.3/5V logic
Supply	Gate supply 10–18V (usually the 12V load supply); load supply up to 24V

Board
Size	40.0 × 30.0 mm
Mounting	4 × M2.5 holes, 2.54 mm from each corner
Connectors	3-pin 2.54 mm header · Screw terminal 2P 5.0mm 17A (THT) — VDRV 10–18V gate supply in · Screw terminal 2P 5.0mm 17A (THT) — Load: V+ and LOAD−
Main IC	UCC27517DBVR (LCSC C99395)
Revision	Rev A

Software
Libraries	Any PWM output (ESPHome `ledc`, Arduino `analogWrite`)

Performance

Capability

Current ratingsFET datasheet vs our board design target.

FET rating80 A

Continuous (this board)10 A

Pinout

Pin map and connections

Pin	Name	Type	Function
1	`VDRV`	Signal	Gate supply 10–18V (also on J1)
2	`GND`	Ground	Ground
3	`IN`	Signal	PWM in, 3.3/5V logic, up to 200kHz

Mechanical

Dimensions and what's in the box

Board 40.0 × 30.0 mm with M2.5 holes — Top view · 40.0 × 30.0 mm

In the box

1 × ET-MD14 High-Current MOSFET PWM Switch (assembled)
1 × 3-pin 2.54 mm male header, unsoldered

Getting started

Wire the header: VDRV, GND, IN
Libraries: Any PWM output (ESPHome ledc, Arduino analogWrite)

Compare

Which load switch?

	High-Current MOSFET PWM Switch (this board)This board	ET-MD13 2-Channel PhotoMOS SSR	ET-MD17 2-Channel High-Side Switch	ET-MD08 4-Channel MOSFET Driver
What it does	Gate-driven 30 V MOSFET for 10 A loads, fast PWM from 3.3 V	Silent solid-state switches, 60 V 1 A AC/DC, logic input	Protected 5–34 V high-side outputs for 12/24 V loads	Four logic-level low-side switches, 3 A each up to 24 V
Interface	PWM up to 200kHz from 3.3/5V logic	Logic high on IN (3.3/5V), ~6–11mA per channel	3.3/5V logic inputs, status (fault) outputs	3.3V and 5V logic, < 1µA
Best for	Heaters and LED strips	Switching low-voltage AC or DC loads silently	Valves and solenoids on 24 V	LED strips and lighting
Price	39 AED	39 AED	25 AED	16 AED

Downloads

Documents and design files

PDFET-MD14 schematicRev A LCSCUCC27517DBVR datasheet and stockC99395

STEP3D modelComing soon

Need a custom version of this board?

Different connector, size or sensor? We design and build custom variants.

Get a design quote Talk to an engineer