ET-D01
HT16K33 4-Digit 7-Segment Display
0.56" red 4-digit display on I²C, Qwiic
AED 39.00
Out of stockOverview
0.56" red 4-digit display on I²C, Qwiic
The ET-D01 is built around the Holtek HT16K33 — 16×8 LED controller with display RAM, 16-step dimming, blink. It connects over I²C 0x70; Qwiic / STEMMA QT and is powered from 4.5–5.5V per datasheet; runs from 3.3V Qwiic hosts at lower brightness.
Two Qwiic / STEMMA QT connectors let you chain it with other boards without soldering, and the 2.54 mm header fits a breadboard.
Designed in Dubai by ElectroTrical — the full schematic, BOM and design notes are published below.
Good for
- Clocks and timers
- Sensor read-outs
- Scoreboards and counters
Key features
What makes it different
Driver
Holtek HT16K33: 16×8 LED controller with display RAM, 16-step dimming, blink
Display
0.56" (14.2mm) 4-digit red 7-segment, common cathode, decimal points
Interface
I²C 0x70; Qwiic / STEMMA QT
Supply
4.5–5.5V per datasheet; runs from 3.3V Qwiic hosts at lower brightness
Qwiic / STEMMA QT
Two JST-SH connectors plus a 2.54 mm header — 3.3 V and 5 V hosts.
Open documentation
Schematic, BOM and layout notes published for every board.
Specifications
Technical specifications
| Driver | Holtek HT16K33: 16×8 LED controller with display RAM, 16-step dimming, blink |
|---|---|
| Display | 0.56" (14.2mm) 4-digit red 7-segment, common cathode, decimal points |
| Interface | I²C 0x70; Qwiic / STEMMA QT |
| Supply | 4.5–5.5V per datasheet; runs from 3.3V Qwiic hosts at lower brightness |
| Size | 50.8 × 25.4 mm |
|---|---|
| Mounting | 4 × M2.5 holes, 2.54 mm from each corner |
| Connectors | 2 × Qwiic / STEMMA QT (JST SH 4-pin) · 4-pin 2.54 mm header |
| Main IC | HT16K33 (LCSC C87502) |
| Revision | Rev A |
| Libraries | Adafruit_LEDBackpack (Arduino), adafruit-circuitpython-ht16k33 |
|---|
| JP1 (default Closed) | Power LED (cut = off) |
|---|---|
| JP2 (default Closed) | I²C pull-ups |
Performance
Digit size
Pinout
Pin map and connections
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | Power | 5V (works from 3.3V, dimmer) |
| 2 | GND | Ground | Ground |
| 3 | SCL | I²C | I²C clock |
| 4 | SDA | I²C | I²C data |
Qwiic / STEMMA QT pins: GND, VIN, SDA, SCL (same on both connectors). I²C pull-ups (10 kΩ) are on the board; cut JP2 to remove them.
Mechanical
Dimensions and what's in the box
In the box
- 1 × ET-D01 HT16K33 4-Digit 7-Segment Display (assembled)
- 1 × 4-pin 2.54 mm male header, unsoldered
Getting started
- Plug in a Qwiic / STEMMA QT cable, or solder the header and wire VIN, GND, SDA and SCL
- Libraries: Adafruit_LEDBackpack (Arduino), adafruit-circuitpython-ht16k33
- Run an I²C scanner to confirm the address: 0x70
Compare
Which segment display?
| HT16K33 4-Digit 7-Segment Display (this board)This board | ET-D03 MAX7219 8-Digit Display | ET-D04 TM1637 4-Digit Display | ET-D02 HT16K33 LED Matrix Driver | |
|---|---|---|---|---|
| What it does | 0.56" red 4-digit display on I²C, Qwiic | Eight 7-segment digits on SPI, daisy-chainable | Large 0.56" 4-digit display on two GPIO pins | Drive 128 LEDs and scan 39 keys over I²C |
| Interface | I²C 0x70; Qwiic / STEMMA QT | SPI (DIN, CS, CLK) with DOUT for daisy-chaining… | CLK + DIO on any two GPIOs | I²C 0x70; Qwiic / STEMMA QT |
| Best for | Clocks and timers | Frequency and voltage meters | Simple clocks | Custom LED matrices and bar graphs |
| Price | 39 AED | 11 AED | 9 AED | 19 AED |
Downloads
Documents and design files
Need a custom version of this board?
Different connector, size or sensor? We design and build custom variants.